Ürün KoduDY13
Stok Var

100 Watt lazer tüpleri ile kullanmak için uygundur.


Mark & Model : DY13, The product is featured as excellent quality and reasonable price, stable performance, improving transfer efficiency and fast-speed breaking. The performance and service time of laser tube will be improved when the CO2 laser tube power supply is equipped which is suitable for Reci W4 laser tube.

Origin : Asia and Pacific Area China

Quality Standard : International

Submit date : 2012-11-28

H.S.Classification : Machinery & Electronics Electr.Element 8541 Semiconductor devices; light-emitting diodes etc.; parts thereof


Product profile 

DY13 Power Supply Instruction

I. Instruction for sub-connection wire of the controlled


1      2    3     4     5    6

5V   TH  TL  WP    G   IN

1) Footer 1 is 5V power supply. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer, and 5V current should be less than 10 mA.

2) TH. TL refers to high and low power level respectively, and WP refers to water protection.

3) Footer 5 G refers to ground, and 6 refers to input end.

4) When connecting the control plate, connect the light signal with footer2 in case of high power        level light-emitting, (footer 3 for low power level light emitting), connect the gwire with footer 5,    connect footer 6 with power controlanalog signal, and make short circuit for footer 4 and 5.

5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, the frequency      should be above 20K.

6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively.

7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection.

8) It is not proposed to control laser power with high frequency modulation, because it will have impact on the service life of the laser.

9) The model is applicable to W4 laser, it is necessary to regulate and use the current according to the laser instructions.

10) The ammeter is concatenated to the cathode line.


II. Instruction for power wire


footer 1


footer 2 footer3

AC 220V 50HZ 10A


Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation.


III. Instruction for laser connection wire

1) The positive red-line with high voltage is connected to the laser tail

2) The negative white-line is connected to laser output window

IV. Current limitation

To limit the working current, the potentiometer (lies in the underside of the power
supply) should be rotated in counterclockwise (please refer to the schematic diagram
in our website: www.recilaser.com). Limit the maximum output current as it is
regulated in the operating instruction. The working current should be limited before


V. Linear scale between input signal and the output current

Turn around the potentiometer, the linear scale will be changed: for example, when the
input signal is 0-5V, the output current is 0-34mA.Or when the input signal is 0-2V, the output signal is 0-34mA.

Note: when the potentiometer is turned down too much, the real output current will be brought down by the same input signal.



VI. Using Current

The use standard for our power supply is under 220V, 50Hz. The fluctuation of the input
voltage and frequency will affect the working current provided by the power supply,
the effection is linear relative. The unstable of the input voltage will affect the output
power of the laser tube. The fluctuation of the input voltage has no effection on
the lifespan of the laser if only the current provided by the power supply is not over
the current limitation.




Beijing Reci Laser Technology Co., Ltd.




Etiketler: reci dy13 güç kaynağı güç kaynağı dy13 reci dy13 reci dy13 power source reci power supply dy13 power source dy13 power supply reci power source

10221 Okunma